Image: 
Contact: 

HP4156A Precision Semiconductor Parameter Analyzer Contact Information:
  Faculty Contact:   Aaron Hawkins 
  Staff Contact:   Don Dawson

 

 

General Description

The Hewlett Packard 4156A Precision Semiconductor Parameter Analyzer is an extremely useful tool for characterizing semiconductor devices. It has up to four probes that can serve as voltage sources, current sources, voltage monitors, and current monitors. These probes are designed to be programmed through a menu-driven user-interface. Possible measurements include, I-V curve of a simple two terminal device, Id-Vds-Vg graphs for MOSFETs, switching characteristics of logical gates, etc.

 

1. Power Button 2. Display 3. 3 1/4 disk drive 4. Soft Keys 5. CHANNELS Menu Button 6. MEASUREMENT Menu Button 7. DISPLAY Menu Button 8. GRAPH/LIST Menu Button 9. SYSTEM Menu Button 10. Thumbwheel (used for moving cursor on graph, or selecting softkey menus) 11. Cursor Movement, and Field Selection buttons - The Fast Key allows the cursor to move faster while in the Graph Mode 12. The SINGLE button - will perform one sweep with the setting that the user has determined, will clear previous graph data 13. The REPEAT Button - will perform continuosly repeating single sweeps 14. The STOP button aborts current measurement 15. The APPEND button will perform a single sweep, without clearing previous graph data 16. Text/Number Entry Keys

Operating Instructions

Programming the HP4156A to do a particular measurement requires stepping through a short sequence of menu screens as follows: 1) Channels Channel Definition This is where the operation of the each of the SMUs (source monitor units - the probes) is defined. A SMU can operate as either a combination voltage source/ammeter or current source/voltmeter. Depending on the type of measurement, you can use 2, 3, or 4 SMUs, and if that isn't sufficient, there are two more dedicated voltage sources (Vs 1 and Vs 2) and two dedicated voltmeters (Vm 1 and Vm 2) that can also be used.

Measurement Mode Sweep Sampling Default Measurement Setup Canned Programs The 4156 has several common measurement setups stored in memory. These can be accessed using the soft keys. Simply punch the appropriate soft key and the setup is done. MEM1: B-Tr VCE-IC MEM2: FET VDS-ID MEM3: FET VDS-ID MEM4: DIODE VF-IF Channels UNIT Specifies which SMU will be assigned to a particular variable, mode and function. VNAME & INAME The names are simply labels that you attach to the particular voltage and current. For instance, if you are measuring a diode, you might label the voltage for one of the SMUs as Vdiode and the current as Idiode. But these are simply names for the variables, the actual names used aren't terribly important. MODE There are three possible MODEs: V (for voltage source), I (for current source), or COMMMON (for the common terminal). There must always be one common terminal, and all voltages will be defined with respect to the common terminal. FCTN Once the MODE of the SMU has been defined, then the FCTN further defines how the SMU will be used. The SMU source will either be CONST (constant), meaning that the voltage or current is fixed at some value, or the SMU can function as a variable source, in which case the voltage or current can be stepped through a sequence of values. There are two choices for the variable, VAR 1 and VAR 2, so that you can change voltages or currents on two SMUs in any given measurement. An obvious example of when you would need two SMUs would be when measuring iD vs. vDS curves for a MOSFET. In that case you would set the gate voltage at some voltage, and then step the drain voltage through a range of values, measuring the current at each point. Then you would change the gate voltage to some new value and measure ID vs. VDS for the new drain voltage. When using both VAR 1 and VAR 2, the 4145 will start by going to the first value of VAR 2, and then step all the of prescribed values for VAR 1. Then VAR 2 will be incremented to the requested value, and VAR 1 will again be stepped through all of its prescribed values. In programming parlance, VAR 1 and VAR 2 work like nested DO-loops, with VAR 1 being the inner loop and VAR 2 the outer loop. A final note: If your measurement requires changing only one variable, you must use VAR 1. User Function Definition

Your own functions - Notice at the bottom of the channel definition page, there are spaces for entering user-defined functions. You won't always want to measure a simple voltage or a current. For instance, in characterizing MOSFETs, it is sometimes useful to measure the square-root of the drain current. User Variable Definition 2) Measure Once you are finished with the channel definitions, you will need to tell the 4156 the range of voltages and currents that you want to measure. This is done on the Measure: Sweep Setup page. Push the NEXT key or the MEASURE key to go there, and you should see a page similar to the one shown below.

Sweep Setup

Sweep Mode The sweep mode determines how the measurement points will be spaced. You can have either a normal linear spacing or a variety of logarithmic spacings. Linear spacing is most common. Notice that these are entered using soft keys. Lin Log Start Voltage/Current at which the sweep will begin Stop Voltage/Current at which the sweep will end Step The increment which the Voltage/Current will vary with each step No. of Steps The number of steps to make sweeping from one Voltage/Current to the next *Note The 4156 calculates the number of steps for VAR 1, using the step size, start, and stop. Curiously, the procedure for VAR 2 is slightly different. For VAR 2, you must enter the starting point, the step size, and the number of steps. Then the 4156 will determine the stopping point for VAR 2. Compliance Next, enter a compliance limit for VAR1. The compliance is a way of protecting the device being measured. If the SMU is used as a voltage source, the compliance is the maximum current that will be allowed to flow through that terminal of your device. If the SMU is a current source, the compliance will be the maximum voltage that will be applied to that terminal of your device. Power Comp. Subtle point: When entering values like the start and stop points you need not enter the standard units (V or A ). However, if you want to enter the value in mV or µV or something like that, you must include the unit prefix. For example, each of the following is a viable way for entering 20 millivolts: 0.02, 20m, 20000u. Timing This is used for Holding or Delaying the sweep measurements for special measurements. Constant Enter values for any constant sources that may be used in your measurement. 3) Display This page is used to set up the graphics display for the data to be collected. It is important to remember that entries here affect only how the data will be plotted - it is independent of the information entered on the SWEEP SETUP page. This means that you could set up the on-screen graph so that none of the collected data would appear! That data is not lost (it's stored in the machine's memory). All you would need to do in such a case is to redefine the graph.

Display: Display Setup

Display Mode You should see the word GRAPHICS following DISPLAY MODE: You can choose other ways to look at the data using the soft keys. GRAPHICS mode is the most commonly used display mode. Sometimes LIST mode is useful. LIST mode displays the raw data in one long list. Graphics Name Choose the variable to be plotted Scale Linear or Log Scale Min & Max Use these fields to determine the ranges in the x and y for your graph. You will have to use your best judgment on these values. If you don't get a nice graph after the measurement, you can always come back to this page and adjust all these settings to give you a better graph. Grid Turns Grid ON and OFF Line Parameter Data Variables Display: Analysis Setup 4) Graph/List This is where all the action occurs. You should see an empty graph, set up according to the entries from the Display Setup Page. To measure data, you need to push one of the measurement keys. SINGLE will cause the 4145 to sweep through the full range of VAR1 and VAR2 points, measuring the current at each point, and plotting the results. Each time you press the SINGLE key, the previous data will be erased and new data plotted in its place. REPEAT has the same effect as continually pushing the SINGLE key - the 4156 will repeatedly sweep through the measurement cycle until you push the STOP key. APPEND is very similar to SINGLE, except that the old data is not erased. You will get two or more plots, with each new one being superimposed over all the previous plots. This is very handy for making comparisons between different devices or for measurements taken under different conditions (eg. with lights on and lights off). Graph/List: Graphics On the lower part of the screen you will notice a number of menus, accesible by pressing the softkeys. Each menus has options which allow you to manipulate the data on the screen. MARKER/CURSOR

MARKER The marker is a point on the graph that the user may define. This may be used to compare similar points of data on several different graphs. MARKER MIN/MAX Pressing this softkey will alternate the marker selection between the min and the max INTERPOLATE The user can turn this off and on DIRECT MARKER/CURSOR This option appears whent the cursor is set to either SHORT or LONG MARKER SKIP AUTO ANALYSIS CURSOR User may choose between OFF, SHORT, and LONG cursors LINE

Options available for graphing lines SCALING

AUTO SCALING It is quite possible that the graphing range you chose on Display Setup Page wasn't appropriate, so that the graph is mostly (or even completely) empty. AUTO SCALE will automatically resize the graph so the data very nearly fills up the whole graph. This is very handy. The only drawback is that the resulting scale is usually an awkward value like 3.29mA/div. If you want a more readable graph, you can use AUTO SCALE to get a rough idea of the range of the data, then go back to the MEAS & DISP SETUP page and pick more sensible ranges. ZOOM IN Zooms in wherever the cursor is centered ZOOM OUT Zooms out wherever the cursor is centered CENTER AT CURSOR Centers the display at the cursors position CENTER TO MARKER centers the display where the marker is loctated CANCEL SCALING cancels all manual manipulations, and reverts to display setup options DISPLAY SETUP

a user might use this menu to change the DISPLAY SETUP options while monitoring the resulting graph SWEEP SETUP

a user might use this menu to change the SWEEP SETUP options while monitoring the resulting graph TIMING SETUP

a user might use this menu to change the TIMING SETUP options while monitoring the resulting graph CONST SETUP Graph/List: List

Marker Marker user may turn marker on and off Direct Marker Marker SKip Next Append Spreadsheet

This is a useful option, as a user can export the graph into a format that is readable in excel, matlab, etc. Name Filename (8 DOS Characters) Unit units can be turned on or off Output data index (1 to 2147483647) Delimiter Determines which character the values will be separated by. Space Comma Tab String Marker Determines how the 4156 will denote a string " " ' ' None Execute By pressing the softkey corresponding to this, the list data will be exported and save in the specified format onto the floppy disk. 5) System

Since the file formats that this menu outputs are not readable by any know program, this menu is is practically useless. It contains file save and get commands, as well as color setting, and other menus that we don't use very much.